FOLLOW US

Post Type: Metal

Phosphor Bronze Cable:
1/8" Diameter, 1X19

A strong finishing statement to your project.

The phosphor bronze cable is a contemporary color alternative to Ultra-tec’s cable offerings. 

  • Designed as a 1/8″ diameter cable.
  • Corrosion Resistant.
  • 1×19 strand cable engineered to hold static loads without stretching and is relatively stiff.

 

Cable Construction 

 1×19 strand cable is engineered to hold static loads without stretching, and it is relatively stiff. Other cable constructions are not offered in the bronze cable option because of their elevated levels of stretch and lower breaking strengths in comparison to 1×19 construction.

 

MINIMUM BREAKING STRENGTH (in lbs.)

FOR 1X19 STRAND TYPE 316 STAINLESS STEEL CABLE

 

Cable Diameter 1/8″
Breaking Strength 1, 780

 

 

Specifications

Cable Diameter Breaking Strength Part No.

1/8”

1,780

 A4P

The Pull-Lock® is a concealed, swageless, non-tensioning, through-the-post-mounted fitting that is suitable for use on level or pitched runs, and is available for 1/8”, 3/16”, and 1/4” diameter 1×19 stainless steel cable.


The Pull-Lock® must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the end post. Using the Pull-Lock® fitting on level or pitched runs requires enough clearance on the back side of the end post to install the fitting through the back side of the post. That amount of clearance depends on the length of Pull-Lock® chosen. This fitting is furnished with a Delrin® washer that is installed between the shoulder of the fitting and the end post to protect the surface of the finish of the end post as tension is applied. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.


This fitting is very much like the Push-Lock®, except the cable passes through the Pull-Lock®, meaning you can just cut the excess cable where it exits the fitting – no need to measure the cable before cutting. This feature eliminates the need for taking accurate cable length measurements (as is required when using a Push-Lock® fitting). For that reason, it is the more popular of the two.


The Pull-Lock® can be used on a pitched run in a hole drilled horizontally through the end post. The cable will exit the fitting at an angle. To properly use this fitting on a pitch, it is recommended that you choose a Pull-Lock® that is the same length as the cross section of your end post.

Specifications

1/8″ Cable  Part No. 3/16″ Part No. 1/4″ Part No.  Frame “F” Frame “R” Frame “P” “L” Length
PUL-4-12 PUL-6-12 N/A 1-1/2″ 1-1/2″ 1-1/4″ 1.562″
PUL-4-12 PUL-6-12 N/A 4″ x 4″ N/A N/A 1.562″
PUL-4-1.810 PUL-6-1.810 PUL-8-22 N/A N/A 1-1/2″ 1.810″
PUL-4-2.030 PUL-6-2.030 PUL-8-32 2″ 2″ N/A 2.030″
PUL-4-2.300 PUL-6-2.300 N/A N/A N/A 2″ 2.300″
PUL-4-2.375 PUL-6-2.375 N/A 2-3/8″ 2-3/8″ N/A 2.375″
PUL-4-3.030 PUL-6-3.030 N/A 3″ 3″ N/A 3.030″
PUL-4-2.530 PUL-6-2.530 N/A 2-1/2″ 2-1/2″ 2-1/2″ 2.530″
PUL-4-3.030 PUL-6-3.030 N/A 3-1/2″ 3-1/2″ 3″ 3.030″

The Push-Lock® is a concealed, swageless, non-tensioning, through-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.


The Push-Lock® fitting must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the end post. Using the Push-Lock® fitting requires enough clearance on the back side of the end post (to install the fitting through the back side of the post) and that amount of clearance depends on the length of the Push-Lock® fitting chosen. This fitting is furnished with a Delrin® washer that is installed between the shoulder of the fitting and the end post to protect the surface of the finish of the end post as tension is applied. It is recommended that you choose a length of Push-Lock® that is the same as the cross section dimension of the end post. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.


This fitting is made to look similar to the Invisiware® Receiver from the exterior of the post, so it is recommended to use a Receiver with stud on the opposite end whenever practical to maintain a consistent look.

Specifications

Metal Framing Options for Push-Lock Fittings

Frame “F”  Frame “R”  Frame “P”  1/8″ Cable Part No. 3/16″ Cable Part No. “L” Length
1-1/2″ 1-1/2″ 1-1/4″ PL-4-12 PL-6-12 1.562″
2″ 2″ 1-1/2″* PL-4-2.030 PL-6-2.030 2.030″
3″ 3″ N/A PL-4-3.030 PL-6-3.030 3.030″

*Will protrude from cable side of post +/- .125″

The Push-Lock® Stud attaches manually with no special tools required. The cable attaches to the fitting via our Push-Lock® locking wedge system. Push- and Pull-Lock® fittings are made entirely of stainless steel components, most of them Type 316.

Specifications

Cable Diameter Part No.
1/8” PLST-4
3/16” PLST-6

The Push-Lock® Tensioner with Threaded Bolt is an exposed, swageless, tensioning, face-of-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.


The Push-Lock® Tensioner with Threaded Bolt can be used with any fitting on the opposite end of the run. This fitting consists of two separate pieces: the threaded bolt and Push-Lock® tensioning body. The threaded bolt is installed into a pre-drilled and tapped hole in the end post. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools. The body threads onto the other end of the bolt, connecting the two pieces. Tension is created by securing the post-side segment of the body onto the machine threads while preventing the cable-side segment of the body from turning.

Specifications

Cable Diameter Part No.
1/8” PL-SFC-MS-4
3/16” PL-SFC-MS-6

The Push-Lock® Tensioner with Threaded Clevis is an exposed, swageless, tensioning, face-of-the-post-mounted fitting that is suitable for level or pitched runs, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable. It is a more compact design than our swaged Adjust-A-Body® fittings.


The Push-Lock® Tensioner with Threaded Clevis can be used with any fitting on the opposite end of the run. This fitting consists of two separate pieces: the articulating threaded bolt and Push-Lock® tensioning body. The threaded bolt is installed into a pre-drilled and tapped hole in the end post. The cable attaches to the body via our Push-Lock® locking wedge system which requires no special tools. The machine thread of the articulating bolt threads into the body, connecting the two pieces. Tension is created by securing the post-side segment of the body onto the machine threads while preventing the cable-side segment of the body from turning.

Specifications

Cable Diameter Part No.
1/8” PL-SFC-MP-4
3/16” PL-SFC-MP-6

Tthe Push-Lock® Threaded Bolt fitting is an exposed, swageless, non-tensioning, face-of-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.


The Push-Lock® Threaded Bolt must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled and tapped hole. This fitting is furnished with a Delrin® washer that is installed between the shoulder of the fitting and the end post to protect the surface of the finish of the end post as the fitting is installed. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.


This fitting is usually chosen one, because you want to use a swageless fitting AND you don’t have access to the back side of the end post; and two, because you want to use a swageless fitting AND you want symmetry with a face mounted tensioner on the opposite end of the run.

Specifications

Cable Diameter Part No.
1/8” PL-FM-MS-4
3/16” PL-FM-MS-6
Push-Lock Threaded Bolt
Push-Lock Threaded Bolt

New for 2016 – the Push-Lock® Threaded Clevis is an exposed, swageless, face-of-the-post-mounted fitting that is suitable for level or pitched runs, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable. It is a more compact design than our
Push-Lock® Threaded Eye.


The Push-Lock® Threaded Clevis can be used with any tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled and tapped hole in the end post. The cable attaches to the body via our Push-Lock® locking wedge system which requires no special tools.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the body of the fitting pivots at the clevis.

Specifications

Cable Diameter Part No.
1/8” PL-CL-RP-4
3/16” PL-CL-RP-6

The Push-Lock® Turnbuckle Threaded Bolt is an exposed, swageless, tensioning, face-of-the-post-mounted fitting that is suitable for level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.


The Push-Lock® Turnbuckle Threaded Bolt can be used with any fitting on the opposite end of the run. This fitting consists of four separate pieces: the threaded bolt, the body, the lock nut, and the Push-Lock® Stud. The short thread of the threaded bolt is secured into a pre-drilled and tapped hole in the face of the end post. The lock nut is installed all the way onto the exposed machine thread of the threaded bolt first, followed by the body. The Push-Lock® Stud threads into the body, and the cable attaches to the stud fitting via our Push-Lock® locking wedge system which requires no special tools. Tension is created by using the body as a turnbuckle. Once sufficient tension is achieved, the lock nut is secured against the body to prevent the fitting from loosening.


The most likely application for this fitting would be when substantial take-up is required AND there is a preference for a swageless fitting, AND there is less than 2-1/2” of space available in back of the end post.

Specifications

Cable Diameter Part No.
1/8” PL-TB-TB-4
3/16” PL-TB-TB-6

SITESEARCH

WHERETO BUY